When is it OK to repair molded materials instead of replacing them?

14 hours ago 3

This article examines the factors which professionals take into account when deciding to repair or replace a vehicle, and when to choose to replace the vehicle rather than repair it.

Complete the Repair vs. Replace Decision Matters

This is not to be taken lightly. Where materials could have been restored, the cost of their replacement is a waste and amounts to unnecessary construction waste. Once mold is too severely damaged to be remediated, however, it will remain in place and will continue to cause health issues, and will likely be the cause of recurring mold and future structural failure.

If your house has permanent musty smell without mold presence, restoration companies also offer odor removal services. 

Can the Material Absorb Moisture?

The most important factor is porosity. Mold absorbs water and when it is attached, it enters material with porosity. Materials like wood and concrete blocks have a moderate porosity. They can be salvaged to a large degree depending on the amount and length of exposure to mold.

What is the extent of contamination?

EPA has a guideline to consider when they want to call in the mold remediation company: When the mold infestation is more than 10 square feet, it should be treated by a professional mold remediation company. In addition to size, the depth of the contamination can be as important.

Where the mold is visible, it is likely to be smaller in size and may be easier to manage than mold that has been present for a longer duration and has infiltrated the interior of the mold. Older infestations tend to be bigger, but may not be much different on the outside.

Are there any flaws in the material’s structure?

Mold eats away at organic material. It gradually decomposes the structure of that which it is growing. Moldy drywall with high levels of moisture gets soft and crumbly. Long term colonization of wood may be a sign of rot. Now these materials will serve no other purpose and need to be replaced if possible or not if the mold can be killed.

How did the mold come into being?

It is a question that many people overlook and others would rather forget to ask, but it shouldn’t be. However, if the moisture source has not been resolved, be it a leaky pipe, inadequate ventilation or waterproofing, then repairing or replacing the affected material will merely be postponing the issue. This will be the same form once more.

The source of moisture must be found and fixed prior to any repair or replacement. This is non-negotiable.

What are materials that are usually repairable?

Early contaminated wood (Solid Wood)

The semi porous bit is solid wood; it depends on the time. If mold is found in the early stages before it has had much time to penetrate the wood grain, in most cases, the mold can be disinfected and sanded and coated with a mold resistant primer or sealant.

This is for structural framing, hardwood floors and solid wood furniture. The difference is between surface mold and mold that is commencing to decay the wood fiber. If mold or stains will be seen through the entire cross section of the wood and if the wood appears to be severely rotten, the wood must be removed.

Concrete and Masonry

Unpainted or unsealed concrete is porous, but the denseness of concrete makes it so that mold rarely penetrates to a great depth. Mold growth on concrete is generally removed with a wire brush and a bleach solution or commercial concrete mold remover solution, and then dried, and treated with a waterproof sealant.

Under dampness for long periods, some concrete may be contaminated to the extent that it is advisable to assess it by a professional before a final decision is taken.

What materials are almost always to be replaced?

Fire protection is provided by drywall and gypsum board.

One of the least mold resistant materials, drywall is designed to absorb moisture. If mold is established it will spread rapidly across the paper facing and gypsum board surface of drywall. Scrubbing the surface does not make a difference to the contamination in the bulk.

Affected areas of drywall should be cut out and replaced. It is the standard industry practice, and the best solution to the problem.

Insulation

Fiberglass Batt and Cellulose insulation contain moisture and provide a breeding ground for mold. It is virtually impossible to effectively remediate mold growing in insulation. The option of replacement is always the best option. Carpet and Padding

Carpet and underlayment holds and retains water. Mold will rapidly grow into the carpet fibers & carpet padding. 

Ceiling Tiles

Traditional acoustical ceiling tiles are porous and will be hard to clean effectively. They also tend to be relatively inexpensive to replace, and in most instances, the only solution. When to call a Professional?

When the mold is found on the outside surface of a non-porous object and is a minor problem, it is suitable to handle the mold removal on your own. If it is not more complicated than that, it’s a job for the professional.

Taking the Right Action given Your Situation.

There is no single solution available for repairing or replacing depending on the circumstances! The decision will be based on the nature of the material, the degree of damage, the duration of the moisture problem, and whether or not the moisture problem has been corrected.

The rule of thumb is that when the material is porous, contaminated and/or structurally unsound, replacement is the more secure and possibly more economical answer in the long term. However, if the material is not porous, light and the source of contamination is under control, then professional cleaning and treatment may be a viable solution for you.

 

The post When is it OK to repair molded materials instead of replacing them? appeared first on The Hype Magazine.

Read Entire Article